Posts

Showing posts from September, 2021

Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total ordered quantity.  Image-Hydro Test (Pressure Release) (Photo Credit: Ritesh Raj)  
Post a Comment
Read more

Bulk Density and Voids of Fine Aggregate

-
Image
 Bulk Density and Voids of Fine Aggregate Types :- (1.) Loose Weight (2.) Rodded Weight  Loose Weight  Image Source:-ScienceDirect.com Apparatus Required - (1) Weighing Balance (2) Temping Rod (3) Straight Edge (4) Fine Aggregate  (5) Observation Sheet (6) Cylindrical metal measure of 3 litres, 15 litres or 30 litres according to the size of coarses particle of aggregate. Image Source:-civilsir.com Recent Post:- Proctor Test for Compaction of Soil  Test Procedure :- (1) For size of particle 4.75 mm and under, cylindrical metal measure of capacity 3 litres is used. (2) For size of particle 4.75 mm to 40 mm cylindrical metal measure of capacity 15 litres is used. (3) For size of particle 40 mm and above, cylindrical metal measure of size 30 litres is used. (4) To start the experiment take the metal measure of 3 litres capacity. (5) Take the empty weight of metal measure=2.686 Kg Also Read:- Bulking of fine aggregate (6) Fill the metal cylinder with loose aggregate to overflowing by means
Post a Comment
Read more

Popular posts from this blog

"Sewer Network Analysis"

-
Image
The word sewerage is made from sewer. The word sewer indicates the usable water which is received from kitchen, bathroom and outfall from toilet/W.C. Every large or small city was held at sea, river and lake and it was planned at initial stage of the project planning, that the dirty water of homes and industries was dumped in that water source easily. Many years passed the dirty water from these utilities are dumped in the nearest source and that source water was make too poisons. Many aquatic life is survive in water and when dirty water is mixed with water source the biological cycle was affected and fishes and other animals population was decreases. Image Source:Pexels.com In that case population of human is also increases continuously and after that level of water source was decreases and we faced many problems continuously. Then sewer network is introduced. Outlet from all homes are connected to lateral lines means the water of kitchen, bathroom and water closet are co
Read more

Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total ordered quantity.  Image-Hydro Test (Pressure Release) (Photo Credit: Ritesh Raj)  
Read more

Methodology for Trenchless Piping by Jack Pushing Method

-
Image
  Methodology for Trenchless Piping by Jack Pushing Method                       Work Under Pit (Photo Credit: Ritesh Raj) 1.0 Purpose: The Purpose of this procedure is to lay guidelines, requirement and to establish a method or a system to control the open cutting & trenchless activity.   2.0 Scope : The Scope of the works covers the laying of RCC Pipe NP4 of 1000mm diameter on LHS of NH (NH No. will be mention) Road from (Chainage 1) to (Chainage 2) by using Trenchless Jack Pushing method.  Also Read: Initial Setting Time of Cement 3.0 Methodology: 3.1 Survey Alignment of Pipe Line to be marked from the position of Manhole to Manhole which is to be constructed. 3.2 List of Manpower: ·          Engineer                                   - As per Requirement ·          Safety Officer                           - As per Requirement ·          Supervisor                                - As per Requirement ·          Excavator Operator                   -
Read more