Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total...
Post a Comment

Important One Liner Questions With Their Answers, Part 9

-


In this article,I am presenting few important one liner questions with their answers, Part-9.These questions could be of your great help to crack exams or for your general awareness about civil engineering. Please go through it.I hope it will expand your knowledge.

Image Source:Pexels.com


(1.) Hydrograhic survey deals with the mapping of-Large water bodies

(2.) If the smallest division of a vernier is longer than the smallest division of its primary scale, the vernier is known as-Retrograde vernier

(3.) Compensating errors in chaining are-Proportional to the square root of the length of the line

(4.) Permissible limits of error in chaining for measurement on rough or hilly ground is-1:250

(5.) Invar tapes is made of an alloy of-Nickle and Steel 

(6.) Chainge is the distance measured-Along a chain line

(7.) In chain survey execute, the first step taken is-Reconnaissance

(8.) If the ores of a soil are completely full of air only, the soil is said to be-Dry soil

(9.) A soil sample has void ratio of 0.5 and its porosity will be close to-33%

(10.) Gradually varied flow is-Steady non-uniform flow


Image Source:Pexels.com


(11.) Bluff body surface-Does not coincide with streamlines

(12.) Centre of pressure on an inclined plane is-Below the centroid

(13.) Separation of flow occurs when pressure gradient-Changes abruptly

(14.) A one dimensional flow is one which-involves zero transverse components of flow

(15.) A body floats in stable equilibrium-When metacentre is above centre of gravity

(16.) At the centre line of a pipe flowing under pressure where the velocity gradient is zero, the shear stress will be-Zero

(17.) When the adhesion between molecules of a fluid is greater than adhesion between fluid and the glass, then the free level of fluid in glass tub dipped in the glass vessel will be-Dependent on atmospheric pressure

(18.) Canal normally used for diversion of flood water of a river is-Inundation Canal

(19.) Intensity of irrigation-is the % of culturable commanded are proposed to be irrigated annually

(20.) The maximum bending stress in an I-beam occurs at the-Outermost fibre

Image Source:Pexels.com


(21.) A support is said to be non-yielding if-The beam has zero slope at the support

(22.) Which sections will be best in torsion?-Hollow circular

(23.) The core of a circular section short column of diameter 'd' is a concentric circular area having a diameter-d/4

(24.) A closed coil helical spring is subjected to a torque about its axis. The spring wire would experience a-Bending stress

(25.) Strength of concrete show an increase with-Increase show an increase with-Increase in rate of loading 

(26.) If the slump of concrete mix is 60 mm, its workability is -Medium

(27.) The durability of concrete is affected by-Both cider and vinegar

(28.) Slump test is a measure of-Consistency

(29.) Shrinkage of concrete is directly proportional to-Cement content

(30.) Approximate value of shrinkage strain in concrete is-0.00003

Image Source:Pexels.com


(31.) For proportion from frost, concrete should be-Dense

(32.) Steam curing is not used with-Rapid hardening cement

(33.) Addition of sugar in concrete results in-Increase in setting time by about 1 hour

(34.) Flash set of ordinary Portland cement paste is-Premature hardening

(35.) Limit state of serviceability of prestressted concrete sections should satisfy-Cracking, Deflection and maximum compression

(36.) Shear span is defined as the zero where-Shear force is constant

(37.) According to Whitney's theory, the maximum depth of concrete stress block in a balanced RCC beam section of depth 'd'-0.53 d

(38.) If 'b' is the width of the plate and 'd' is the diameter of the rivet, then the efficiency of a riveted joint having diamond riveting is given by-(b-d)/b

(39.) Angle of inclination of the lacing bar with the longitudinal axis of the column should preferably be between-40 degree to 70 degree

(40.) The effective length of battened column is increased by-10 %

Image Source:Pexels.com

(41.) The buckling load in a steel column is-Related to length

(42.) An angle section can be used as purlin when slope of the roof truss is-Less than 30 degree

(43.) For unstiffened flange of a beam in flexural compression, the maximum allowble outstand is equal to-16 t

(44.) The problem of lateral buckling can arise only in those steel beams which have-M.I. about the bending axis smaller than the other

(45.) The device used for the easy separation of dry dust of 10 to 100 micro meter size is-Cyclone

Image Source:Pexels.com


(46.) Slate and marble stone belong to-Metamorphic rocks

(47.) Hollow bricks are generally used with the purpose of-Providing insulation against heat

(48.) The lime which has the property of setting in water is known as-Hydraulic Lime

(49.) Bullet proof glass is made of thick glass sheet and a sandwiched layer of-High strength plastic

(50.) If the rocks are formed due to alteration of original structure under heat and excessive pressure, then they are known as-Metamorphic

(51.) The shape of the brick gets deformed due to rain water falling on hot brick. This defect is known as-Chuffs 

Image Source:Pexels.com





Has this page been helpful to you? If yes, please mention in the comment box.




      Thanks for visiting this site.




Written By- 
Ritesh Raj
Email Id-rajritesh.motiharirr@gmail.com


















 

Comments

Post a Comment

If you have any suggestions and doubts please let me know.

Popular posts from this blog

"Sewer Network Analysis"

-
Image
The word sewerage is made from sewer. The word sewer indicates the usable water which is received from kitchen, bathroom and outfall from toilet/W.C. Every large or small city was held at sea, river and lake and it was planned at initial stage of the project planning, that the dirty water of homes and industries was dumped in that water source easily. Many years passed the dirty water from these utilities are dumped in the nearest source and that source water was make too poisons. Many aquatic life is survive in water and when dirty water is mixed with water source the biological cycle was affected and fishes and other animals population was decreases. Image Source:Pexels.com In that case population of human is also increases continuously and after that level of water source was decreases and we faced many problems continuously. Then sewer network is introduced. Outlet from all homes are connected to lateral lines means the water of kitchen, bathroom and water closet are co...
Read more

Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total...
Read more

"Solar Power System"

-
Image
When the energy received by earth from the sun is known as “solar energy”. Solar energy is comes under renewable energy. Solar radiation is the utilized by the solar plates for further use. The working procedure of solar system is capture, convert and then distribution. Image Source:Pexels.com Solar system is categorized in two parts:- (1.)   Passive Solar: -   In this system the selected material have light dispersion properties and designing spaces that the circulate air naturally. This system reduces the need for alternative resourcs and generally focuses on demand side technologies. (2.)   Active Solar:- This system is based on photovoltaic modules (i.e. also known as photovoltaic panels) and collectors of solar thermal system to convert sun light into their useful output. Its increases the supply of energy. Image Source:Pexels.com Recent Post: Different energy sources Working Procedure:- In this system with the u...
Read more