Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total ordered quantity.  Image-Hydro Test (Pressure Release) (Photo Credit: Ritesh Raj)  
Post a Comment

Civil Engineering Technical Terms

-



        Civil Engineering Technical Terms

From this page, you will know civil engineering technical terms better.
                       
Image Source:Pexels.com

 FAR- Floor Area Ratio

DPC-Damp Proof Course

B.M-Bench mark

BOQ-Bill of Quantities

C. I. Pipe-Cast iron pipe

C. I. Sheet-Corrugated Iron sheet

CC-Cement concrete

CJ-Construction Joint

CRW-Concrete Retaining Wall

DPR-Daily Progress Report

DL-Development Length

EMP-Environmental Management Plan

EGL-Existing Ground Level

FL-Floor Level

GL-Ground Level

HFL-Highest Flood Level

 LWC-Light Weight Concrete

MB-Measurement Book

MFL-Maximum Flood Level

MPR-Monthly Progress Report

Image Source:Pexels.com

 MRC-Material Receipt Challan

NBC-National Building Code

OGL-Original Ground Level 

PC-Precast Concrete

PPE-Personal Protective Equipment

PVC-Polyvinyl Chloride

QMP-Quarterly Management Plan

R.B.W.-Reinforced brick work

TBM-Temporary Bench Mark

VP-Vertical plane

HP-Horizontal Plane

WO-Work Order
          
Image Source:Pexels.com

See Also:List of Construction Companies in India

Quality Related:-

FM-Fineness Modulus

C.T.M.-Compressive Testing Machine

QA/QC-Quality Assurance and Quality Control

TPI-Third Party Inspection

TM-Transit Mixer

PQP-Project Quality Plan

QMP-Quality Management Plan

FQP-Field Quality Plan

QAP-Quality Assurance Plan

QCP-Quality Management Plan

SOP-Standard Operating Procedure

ITP-Inspection and Test Plan

CM-Construcrtion Management

QMS-Quality Management System

TQM-Total Quality Management


Image Source:Pexels.com

Posts Related:-

AE-Assistant Engineer

CE-Chief Engineer

JE-Junior Engineer

PM-Project Manager

PWD-Public Works Department


PD-Project Director

DPD-Deputy Project Director

APD-Assistant Project Director

AM-Assistant Manager

DPM-Deputy Project Manager

GM-General Manager

DGM-Deputy General Manager

AGM-Assistant General Manager

AVP-Assistant Vice President

VP-Vice President

CE-Chief Engineer

SDO-Sub Divisional Officer

Image Source:Pexels.com


Institute Related:-

ISI-Indian Standard Institute

ASTM-American Society for Testing & Materials

BIS-Bureau of Indian Standards

ISO-International Organization of Standardization

SI Units-International System of Units

NSC-National Safety Council

WSC-World Safety Council

Image Source:Pexels.com


Safety Related:-

HSE- Health Safety and Environment

OHSAS- Occupational Health and Safety Assessment Series

HIRA - Hazard Identification and Risk Analysis

IOSH-Institute of Occupational Safety and Health

NIBOSH-National Examination Board in Occupational Safety and Health

JSA-Job Safety Analysis

JHA-Job Hazard Analysis

LTA-Loss Time Accident

LTI-Loss Time Injury

LTIF-Loss Time Injury Frequency

PPE-Personal Protective Equipment

SOP-Safe Operating Procedure

SWL-Safe Working Load

LOTO-Log out Tag Out

FAC-First Aid Case    
Image Source:Pexels.com

NFPA- National Fire Protection Association
PTW-Permit to Work
PEL-Permissible Exposure Limit
CPR- Cardio Pulmonary Resuscitation

SCBA- Self Content Breathing Apparatus
SCUBA-Self Content Under water Breathing Apparatus
PFAS-Personal Fall Arrester System

FFE-Fire Fighting Equipment

SWP-Safe Work Procedure

LEL-Lower Exposure Limit

ULE-Upper Exposure Limit

PPM-Parts Per Million

EMS-Emergency Management System

MSDS-Material Safety Data Sheet

ERP-Emergency Rescue Plan

TBT-Tool Box Talk

UA-Unsafe Act

UC-Unsafe Condition





     
Has this blog been helpful to you? If yes, please mention in the comment box.



Thanks for visiting this site.


Written By-
Ritesh Raj
Email Id-rajritesh.motiharirr@gmail.

Comments

Post a Comment

If you have any suggestions and doubts please let me know.

Popular posts from this blog

"Sewer Network Analysis"

-
Image
The word sewerage is made from sewer. The word sewer indicates the usable water which is received from kitchen, bathroom and outfall from toilet/W.C. Every large or small city was held at sea, river and lake and it was planned at initial stage of the project planning, that the dirty water of homes and industries was dumped in that water source easily. Many years passed the dirty water from these utilities are dumped in the nearest source and that source water was make too poisons. Many aquatic life is survive in water and when dirty water is mixed with water source the biological cycle was affected and fishes and other animals population was decreases. Image Source:Pexels.com In that case population of human is also increases continuously and after that level of water source was decreases and we faced many problems continuously. Then sewer network is introduced. Outlet from all homes are connected to lateral lines means the water of kitchen, bathroom and water closet are co
Read more

Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes

-
Image
Important Points SOP (Standard Operating Procedure) During the Inspection of RCC NP4 Pipes: -    Image-Hydro Test (Photo Credit: Ritesh Raj) (1.) Firstly, approved QAP will be checked.  (2.) ID marks should be marked on the inner and outer sides of pipes.  Image-ID Mark (Photo Credit: Ritesh Raj)  (3.) To check the inner and outer diameter of pipes.   (4.) Smooth finishing and before dispatch of RCC pipes cement slurry or grouting where required.   (5.) Load test is required for RCC pipes as per IS codes. It is different for each dia, of RCC pipes.  Image-Plate Load Test (Photo Credit: Ritesh Raj)   (6.) Concrete mix design checked and in which cement content, cement brand, and water-cement ratio should be checked.  (7.) The straightness test to be checked of RCC pipes through the straightness rods to collinear visible.   (8.) As per requirement 2% of hydro tests are to be checked as IS:458 of the total ordered quantity.  Image-Hydro Test (Pressure Release) (Photo Credit: Ritesh Raj)  
Read more

Methodology for Trenchless Piping by Jack Pushing Method

-
Image
  Methodology for Trenchless Piping by Jack Pushing Method                       Work Under Pit (Photo Credit: Ritesh Raj) 1.0 Purpose: The Purpose of this procedure is to lay guidelines, requirement and to establish a method or a system to control the open cutting & trenchless activity.   2.0 Scope : The Scope of the works covers the laying of RCC Pipe NP4 of 1000mm diameter on LHS of NH (NH No. will be mention) Road from (Chainage 1) to (Chainage 2) by using Trenchless Jack Pushing method.  Also Read: Initial Setting Time of Cement 3.0 Methodology: 3.1 Survey Alignment of Pipe Line to be marked from the position of Manhole to Manhole which is to be constructed. 3.2 List of Manpower: ·          Engineer                                   - As per Requirement ·          Safety Officer                           - As per Requirement ·          Supervisor                                - As per Requirement ·          Excavator Operator                   -
Read more